If what I'm understanding is the problem, in some CVL-managed points like the one you're stopped, you need to press Tab to activate the signal, as mentioned in the tutorial
Screenshots & Videos
Moderator: senjer
Re: Screenshots & Videos
In a previous post I showed some of the cabin parts I have of an SG2. Those are enormous, heavy and large. I have a smaller setup on a breadboard, which is very similar to the larger components as far as controlling and reading them with an Arduino. (The speedometer on the large panel is controlled via 0 - 2v, but going from binary driven segments to pwm is easy).
This is a video of one of those series setups on a breadboard, showing the current train speed.
https://youtu.be/baR2lkTRu5c
Why on a breadboard? Both for ease of use and maybe in the future I'll turn this into a guide. Soldering is a big hurdle for some people, a breadboard is easy to follow along. If I have the the prototype all working in software, I'll turn this into a prototype board.
The components are simple, 3 shift registers and 3 seven-segment led displays, a few resistors and an Arduino micro. My caps are all gone, otherwise there would be a decoupling small cap between each shift register. Firmata is used to communicate from the sim to the Arduino. (Not FirmataStandard, just sending over a few strings, the Arduino does the heavy lifting. My C is better than my python).
This is a video of one of those series setups on a breadboard, showing the current train speed.
https://youtu.be/baR2lkTRu5c
Why on a breadboard? Both for ease of use and maybe in the future I'll turn this into a guide. Soldering is a big hurdle for some people, a breadboard is easy to follow along. If I have the the prototype all working in software, I'll turn this into a prototype board.
The components are simple, 3 shift registers and 3 seven-segment led displays, a few resistors and an Arduino micro. My caps are all gone, otherwise there would be a decoupling small cap between each shift register. Firmata is used to communicate from the sim to the Arduino. (Not FirmataStandard, just sending over a few strings, the Arduino does the heavy lifting. My C is better than my python).
Re: Screenshots & Videos
with the introduction of all the beautiful Avenio trams in Hageningen, this means the inevitable end of the 12G trams in Hageningen!
be well, old tram
be well, old tram
- Attachments
-
- Einde 12g tram.PNG (293.96 KiB) Viewed 1916 times
- Alfacinha315
- Posts: 1033
- Joined: 16 Sep 2016, 14:20
Re: Screenshots & Videos
An unusual situation, on my today's journey to Rijndam Westplein. There was a couple of RR-DDM which had a fault at Rijndam Molenwijk depot.
Therefore, SG4 9007 and 9008 ran on the RR1 line. Here, we can see them at the 08h05 Sprinter service, from Noordvliet to Rijndam Molenwijk.
That was a big surprise for me, as I thought this rolling stock was out of service. Good to see RijndamRail gave it a new opportunity.
Therefore, SG4 9007 and 9008 ran on the RR1 line. Here, we can see them at the 08h05 Sprinter service, from Noordvliet to Rijndam Molenwijk.
That was a big surprise for me, as I thought this rolling stock was out of service. Good to see RijndamRail gave it a new opportunity.
- Attachments
-
- Noordvliet.jpg (353.58 KiB) Viewed 1825 times
-
- Noordvliet_2.jpg (374.51 KiB) Viewed 1825 times
Greetings from Lisbon, the capital city of Portugal.
- Leipzig_LP
- Posts: 365
- Joined: 03 Aug 2021, 16:42
- Location: Leipzig (Sachsen) Germany
- Contact:
Re: Screenshots & Videos
The evening movers stop here at Centrum
Metro Sim Beta is a really great game.
- Leipzig_LP
- Posts: 365
- Joined: 03 Aug 2021, 16:42
- Location: Leipzig (Sachsen) Germany
- Contact:
Re: Screenshots & Videos
Due to an error in the control center of the Rijndam transport company, the T4 was accidentally routed to Denia instead of the planned Garenmarkt shortly after
Passing the canalstreet stop, the ATB security system disappeared with the problem that the train then drove to WestWoud without surveillance. At the WestWoud stop, the tram was towed to Denia with a TFS tram.
Passing the canalstreet stop, the ATB security system disappeared with the problem that the train then drove to WestWoud without surveillance. At the WestWoud stop, the tram was towed to Denia with a TFS tram.
Metro Sim Beta is a really great game.
-
- Posts: 587
- Joined: 16 Mar 2019, 17:47
- Location: Glasgow, Scotland
- Alfacinha315
- Posts: 1033
- Joined: 16 Sep 2016, 14:20
Re: Screenshots & Videos
A couple of RET SG2 passing Noordvliet, on test runs between Rijndam Noorderpoort and Panbos.
This picture was taken at 3 am. So, as the first metro between Noorderpoort and Keteplein only departs at 6h09, this consist was delivered back to the Noorderpoort metro sidings, just in time.
24/01/1985
This picture was taken at 3 am. So, as the first metro between Noorderpoort and Keteplein only departs at 6h09, this consist was delivered back to the Noorderpoort metro sidings, just in time.
24/01/1985
- Attachments
-
- Noordvliet_1985.jpg (212.73 KiB) Viewed 1345 times
Greetings from Lisbon, the capital city of Portugal.
- Alfacinha315
- Posts: 1033
- Joined: 16 Sep 2016, 14:20
Re: Screenshots & Videos
BR 47635 "Jimmy Milne" + two NS ICRm BDs calling at Rijndam Zuid, on the 12h15 Sprinter service from Denia to Rijndam Centraal.
25/01/2022
25/01/2022
- Attachments
-
- Rijndam Zuid.jpg (349.29 KiB) Viewed 1194 times
Greetings from Lisbon, the capital city of Portugal.