Re: Rijndam
Posted: 01 Nov 2017, 15:00
I found it in the CVL, but the numbers are not working 
.. The tracks wont change line!
.. The tracks wont change line!You probably typed the wrong track number combination.
Page 146 of 347
Re: Rijndam
Posted: 01 Nov 2017, 15:38
Re: Rijndam
Posted: 01 Nov 2017, 16:10
Re: Rijndam
Posted: 02 Nov 2017, 15:19
Luckily it opens also when you get close to it.. Just can't figure the path number to get out of there properly
Re: Rijndam
Posted: 03 Nov 2017, 15:33
Re: Rijndam
Posted: 03 Nov 2017, 20:33
Nawh, He just used the magic words: Open Sesame.
Re: Rijndam
Posted: 05 Nov 2017, 15:02
Hope to see a diesel locomotive in Depot Molenwijk too 
And a proper code if you just want to drive around with AI, as NN (no stopping, or however it's translated) puts you automatic routes.
And a proper code if you just want to drive around with AI, as NN (no stopping, or however it's translated) puts you automatic routes.
Re: Rijndam
Posted: 05 Nov 2017, 15:18
NN is used in Rijndam in the Depot Transfer activity; that's why you get an automatic route (if you use a CTD file, like during an activity or if you loaded the CTD in exlore mode yourself.
The code (of more specific the end letter N) puts "Niet Instappen" on the displays on the platforms, meaning "Do not board".
If you want to use a code that does not result in the CTD file making paths for you, I suggest using the last letter X (for example; 9991XX of 9991NX). On the platform displays this will result in "Gereserveerd" ("Reserved"), and no automatic paths will be set.
If you open the CDT, and change <destinationcode code="X" id="2" into <destinationcode code="X" id="1", this will result in "Niet Instappen" on the platform displays when using the letter X.
Re: Rijndam
Posted: 06 Nov 2017, 14:01
Thanks for the reply!Sjoerd wrote: ↑05 Nov 2017, 15:18NN is used in Rijndam in the Depot Transfer activity; that's why you get an automatic route (if you use a CTD file, like during an activity or if you loaded the CTD in exlore mode yourself.
The code (of more specific the end letter N) puts "Niet Instappen" on the displays on the platforms, meaning "Do not board".
If you want to use a code that does not result in the CTD file making paths for you, I suggest using the last letter X (for example; 9991XX of 9991NX). On the platform displays this will result in "Gereserveerd" ("Reserved"), and no automatic paths will be set.
If you open the CDT, and change <destinationcode code="X" id="2" into <destinationcode code="X" id="1", this will result in "Niet Instappen" on the platform displays when using the letter X.
Got one more question, is it possible to change the destination name yourself?
<destinationcode code="X" id="2" name="Gereserveerd"/> to <destinationcode code="X" id="2" name="Ei matkustajille"/> , but it shows "Gereseveerd" in the platform screen.
Thank you
Re: Rijndam
Posted: 06 Nov 2017, 16:23
No. ID 2 is always "Gereserveerd". The list with available destination ID's is in the same file, just below it.
It is not a dynamic text; it is just a texture with a destination that is shown, which is selected by the ID number.
It is not a dynamic text; it is just a texture with a destination that is shown, which is selected by the ID number.